HIGH VACUUM PUMP PLATES, GAUGES, OIL, AND EXHAUST FILTERS
SCROLL DOWN TO VIEW ALL OF THE PUMP ACCESSORIES WE OFFER.
HIGH VACUUM PUMP PLATE
THE FISCHER TECHNICAL HIGH VACUUM PUMP PLATE IS MADE OF CAST IRON AND ACCOMMODATES BELL JARS UP TO 9" DIAMETER. THE PLATE IS 1/2 INCH THICK AND NICKEL PLATED FOR CORROSION RESISTANCE. THE HOSE BARB IS 3/8". PUMP PLATE COMES WITH AN ATTACHED VACUUM RELEASE VALVE AND A RUBBER GASKET FOR A TIGHT SEAL. REPLACEMENT GASKETS ARE AVAILABLE.
ACRYLIC HIGH VACUUM PUMP PLATE
THE FISCHER TECHNICAL ACRYLIC PUMP PLATE ACCOMMODATES BELL JARS UP TO 9" WITH A 3/8" INTAKE PORT FOR VACUUM TUBING. THE ACRYLIC BASE HAS FOUR SUCTION CUP STANDS AND THE PLATE IS 10.75" DIAMETER BASE X 1.5" HIGH. PUMP PLATE COMES WITH AN ATTACHED VACUUM RELEASE VALVE AND A RUBBER GASKET FOR A TIGHT SEAL. REPLACEMENT GASKETS ARE AVAILABLE.
HIGH VACUUM HAND HELD GAUGE
THE GAUGE FEATURES A DIGITAL DISPLAY WITH SOLID STATE CIRCUITRY. THE VACUUM RANGE IS 25-12000 MICRONS. IT WILL READ IN 7 INTERNATIONAL UNITES: MICRONS, PSIA, InHg, mBARS, PASCALS, TORR, AND mTORR. THE GAUGE WILL SAVE THE LAST READOUT AFTER SHUTDOWN AND HAS AN 800 PSI MAXIMUM PRESSURE TOLERANCE. THE TOUCH BUTTONS ARE SEALED TO PROTECT AGAINST SPILLS AND DUST. ONE 9 VOLT BATTERY IS REQUIRED (NOT INCLUDED)
HIGH VACUUM PUMP EXHAUST FILTER
THE PUMP EXHAUST FILTER ELIMINATES SMOKE FROM THE HIGH VACUUM PUMP EXHAUST BY REMOVING OIL MISTS. THIS WILL PROTECT THE WORKING ENVIRONMENT, REDUCE NOISE LEVELS, AND MAINTAIN A RETENTION EFFICIENCY OF 99.9% AT .1 um WITH LOW FLOW RESISTANCE
HIGH VACUUM PUMP OIL
FISCHER TECHNICAL HIGH VACUUM PUMP OIL IS AVAILABLE BY THE QUART IN PACKS OF TWELVE.
OIL-001 (ONE QUART)
OIL-012 (CASE OF TWELVE)
HIGH VACUUM TUBING
THE FISCHER TECHNICAL HIGH VACUUM TUBING HAS AN ID OF 1/2 INCH AND CAN WITHSTAND 25 MICRONS OF PRESSURE; AVAILABLE BY THE FOOT OR IN A PRE-CUT FIVE FOOT SECTION WITH TWO HOSE CLAMPS.
HVG-TUBING (PER FOOT)
HVG-TUBING/SET (FIVE FOOT SECTION WITH TWO HOSE CLAMPS)
Change your vacuum pump oil with ease! Simply open the cap on the side of The Tank, place our vacuum pump in the cradle and open the drain valve on the pump to drain. The Tank holds up to 5 oil changes.
High Vacuum Grease
This vacuum grease helps provide a proper seal between the vacuum pump plate and the bell jar so that high vacuum pressures can be achieved.
High Vacuum Inline Air Filter
This air filter which connects inline between the vacuum pump and the vacuum system traps particles as small as 40 microns. The filter can also handle up to 10 CFM of vacuum pressure.
Glass Bell Jars
We carry three sizes of bell jars, which are all suitable to work with our vacuum pump plates #GA-001 and #AP-001. They are made of heavy molded glass to withstand high vacuum pressure. Comes with a knob top for easy handling. The flange has been ground down to provide an excellent seal
BJAR3- 8 1/2 x 15"
High Vacuum Pump Shutoff and Vacuum Release Ball Valve
Our three-way brass ball valve with T-full port and 3ea. 3/8" Hosebarb connections will hold a vacuum in your system, isolate the vacuum pump to prevent oil backup, and release/bleed air back into your system all in one. An external vacuum gauge can be connected to the third valve to take a system vacuum reading isolated from the vacuum pump.
Fischer Technical Company
Manufacturer's Representatives for Scientific and High Vacuum Sales